- need some help please
- dave rudisil
- dave rudisil
- Virtual Crew Chief for Open Wheel Modifieds
- alternator ??????
- wraps best prices and design work
- shocks
- UCA"s on an S10 chassis
- lost on 441
- Right Front Brake
- Tires
- camaro vs monte carlo
- Cast Iron Block
- powerglides
- 7.5 rear disc
- round tube chassis
- tracbar/ panhard bar
- Saginaw 3 speed 3 rings
- rear weight
- starving racer
- parts for sale
- Please Help Me......
- Getting More Rear Brake in Metric
- Ford 9" under a Caprice
- schoenfeldheaders
- right rear spring location vs. left rear location
- setup opinion
- Need help getting more rear weight
- Trailing Arm bearings
- loose racecar
- Need Help Setting My Car Up
- 4 wheel disc brakes
- Powerglide coupler question
- Camaro frames?
- Siping/grooving Hoosier G-60 dirt boss's
- Pic Request G Body cross member notching
- Any one rebuilds steering boxes????
- shocks
- .810 rotors
- front end help
- 305 V-8 Exhaust Manifolds
- leaf spring question
- 350 manifolds (not allowed Rams Horn)
- asphalt to dirt
- rear control arm angle
- Leaf Springs with a pull bar?
- What type of header to use?
- what gear
- 2000 Polaris Trailboss 325 $1800 obo
- Panhard bar or jbar
- Weight %
- trie pressure?
- metric front steering help
- Tire repair
- afco shocks???????????
- Ball joints
- Rotchester carbs
- Leaf Question
- 73 camaro cage question.
- Torque Sensing Diff
- u-joint?
- Best Gm Clip?
- Carb Gasket
- Renegade Custom Suspensions
- Hoosier RC4 and RC6 tires
- trailing arm angles
- disc brakes on a metric
- Canadian Intakes
- Hydraulic clutch cylinder question
- Metric Front-end
- saginaw 3 speed
- Camero leaf help and ???
- Push Rod Trailing arm??????
- electric fan???
- Pinion angle...... How much is too much??
- making a fan shroud
- 5x5 spindles
- Ideas
- Need help with stock spring setup!!!!
- Ford Engine Help
- need help setting up nova?
- Monte Carlo set-up help
- Rookie Cam question
- question on upper control arms camaro
- Powerglide?
- Brake Pads
- gears
- gears
- Shock Help
- What does RACE GAS cost YOU per gallon?
- Camaro and Nova
- moment center on 76 nova
- short water pump alternator bracket
- belts coming off at high rpms
- D.O.T. street tires on beadlock wheels?
- pics of my limited car im building..
- voodoo chassis?
- 1981 monte carlo basic frame height setup???????
- Aussie Racer......
- Macon, Spring and gear help.
- carb help
- Tire Spin
- 3/8 mile high bank gear set up?
- Camber Help
- UMP Sportsman
- cooling fans
- Front Suspension help???
- Rear end upper trailing arm bushing?
- need help with forwar bite
- stagger ?
- Metric front end ideas and help
- front driveshaft yoke
- Need Help With Setup
- Camaro "Fastboys" leaf help?
- Carb. problems
- over heating problem
- Exhaust manifold help
- chevy head questions ????
- camaro RR floating
- Camaro roll cage
- I need help on weights
- any tips would be appreciated!!!!
- Power Steering Pump Alternative
- EQ Hobby/B-mod heads
- Sway Bars for GM G-body
- help please
- Metric front end geometry
- U Joints
- Metric Help
- brake booster on metric GM
- jetting
- cross
- 165cc dart heads
- metric vs old school lower control arms
- metric/dirt left side percentage
- spark plugs
- set up help
- taller ball joints- metric
- Stock Clutch Help Needed..!!
- Still need more forward bite
- IMCA Metric Rear Ride Heights
- Unibody rollcage
- Cooling Problems..
- Best Rods For Street Stock Engine
- Anyone running a 76 and up nova???
- motor ?
- crazy metric setup
- tranny ?
- shocks for my pic-up???????
- Turning in
- setup help
- 79 camaro loose condition
- Best Rochester Carb
- motor setback ?
- 3/8 gear question
- '75 Chevelle spindle question
- caprice help
- set up help
- Setup Question
- UMP difference than IMCA Metric
- starter
- steering quickner
- lawrenceburg pure stock rules
- Stripping dist. gear on sbc
- chassis school!
- For Sale: 2 Tickets to NASCAR Truck Series at KY Speedway
- 15.2 to 1 too much for 500 CFM Carb?
- Chassis Help
- Brake problems
- need timming prolbem help
- coleman rearend
- question
- 2bbl Holley Question
- g-body floor pan brace
- rear spring pockets at lawrenceburg
- street stkgear
- Rod bolt torque.
- bubble test
- fast boy setup
- SBC engine raiseing!!!???
- Batesville gear-street stock
- trailing arms
- 4 link metric
- Fairbury SS help
- Best street stock frames
- 5.7-6.0 rod help
- three wheeling
- bilstein shocks
- cylinder head gurus
- front wheel weights
- gear ?
- chevy flywheels
- Keeping the Motor Cool
- loose on 1/3 mile asphalt
- willys carb
- Clutch Problems
- Rear spring hight and weight
- Scattershield
- Stock mini starter
- convert a 4412 to e-85
- four link rear
- three wheeling
- crossweight
- revving engine during caution?
- Help with setup
- Relocating oilfilter sbc?
- Hobby chassis
- Spindle Question
- metric upper and lower trailing arm mounts?
- steering gear box
- springs on metric dirt car
- question on setup
- question on setup
- trailing arm ?
- The 411 on shocks.
- Harris video ?
- Rules are out for the $5,000 to win 4 cylinder stock race at Screven!
- Metric wheelbase
- impala or metric chassis
- rear brake problems
- Help with leaf springs
- 20in spring lr need more right side body roll
- tire pressure vs spring rate
- Three wheelin shock valving
- 16in rear springs metric
- 20in spring lr metric what length on rr
- powerglide help
- Metric LS Clip & SS Clip diff?
- Low Oil Pressure
- Rear Springs
- Best Steel Bodied Shocks for pro stock?
- Chevy Spindle Kingpin Angle ??
- Floater Rearend
- Caster & Camber
- tire help
- spindles / a arms
- High Rpm power loss
- roller cam
- setup help
- holley floats
- Need expert advise!!!
- A Big thanks
- intake question?
- gearing with tires
- 20in LR Sprng Base Setup
- Bead locks
- 9" in a '91 Camero
- 89 fire bird motor swap
- 400 sbc
- Undersized Caliper Question